R6 Pro SETUP
General info
Full HD resolution (1920×1080) is recommended. Only if you have a very strong system you should use higher resolutions
Always wait in main menu until menu shows up
Before each cheat launch make sure the Raspberry Pi is freshly booted (wait 120 seconds after pluggin in the cable) before opening VanuriClient
Never run VanuriClient and the game at the same time
Don’t launch R6 with Vulkan Mode
Some ISPs like Xfinity have advanced security, making you crash on login in our client. You can turn off advanced security in your phone app.
For Laptop users: You will need to turn on "use dedicated GPU only" mode aka MUX switch. This is usually done in the software from the laptop manufacturer itself.
1. Windows Setup
Install all Windows Updates
Disable Anti-Virus
DefenderControl Download, extract and run it (Password : sordum)
Disable any color adjustemnts
Disable HDR
Restart PC
2. VanuriClient Setup
Download VanuriClient
Log in with your VANURI username and password
A System Check window will appear, install / do all of the required checks
Restart PC
3. Game Setup
Start R6 without cheat
Use supported resolutions, FHD – 2K (no UW)
Have the same resolution on Desktop and in Game
Brightness to default (50)
Windowed Borderless
Accessibility Settings to default
HUD size to default
Don’t run unlimited FPS
Crosshair color needs to be red (default color)
Close R6
4. Flash micro SD-Card
Start VanuriClient and log in with your username and password and select your cheat
The first setup assistance starts, follow it’s instructions (Supported micro SD-Card sizes: 8GB, 16GB, 32GB & 64GB)
Once it flashed your micro SD-Card successfully, you can put your micro SD-Card into your Raspberry Pi
5. Raspberry Pi Setup
Connect Raspberry Pi with the ethernet cable
Connect the USB-C to USB-C/ USB 3 cable from your Raspberry Pi to your PC (use a USB-C/ USB 3 port at the back of your computer, don’t use front ports)
Wait at 120 seconds for the Raspberry Pi to start
Click on “Find Hardware”, VanuriClient will find your Raspberry Pi and apply flashes + spoofs
It doesn’t find my Raspberry Pi -> See TROUBLESHOOTING 1
You should now be able to plug in your mouse into Raspberry Pi and move it
Mouse doesn’t move -> See TROUBLESHOOTING 2
Click “Launch Cheat” to start a unique build, cheat will automatically open after some time
6. Launching Cheat
Open VanuriClient and log in with your VANURI username and password and select your cheat
Click on “Launch Cheat”, VanuriClient might load some more dependencies, just wait for it
If your unique build is ready, VanuriClient will close and tell you to start the game
Wait in menu until the cheat UI pops up, it might pop up behind the game window
7. Cheat usage
INSERT KEY on your keyboard starts / stops the cheat
You would stop the cheat, change the config to your liking and start the cheat
You can start / stop as often as you want
Cheat should always show you your current gun and operator
Set FOV like you have it in Game
Set sens like you have them in Game
Hip = Horizontal sens
1x = 1x Scope Sens
2,5x = 2,5x Scope Sens
3,5x = 3,5x Scope Sens
Set Aspect Ratio like you have it in Game
Recoil: You select your weapon and adjust Y (down) and X (left / right) value to control the recoil, you do that for each weapon.
Aimbot smooth: the lower the faster, if you go too low aimbot will wiggle and overaim
TriggerBot: You hold the TriggerBot key, once there is visual change at your crosshair, it will shoot once (it’s good for holding angles and snipers)
8. Recommended Settings
Aim Key: Left Mouse Button
Aim FOV: 40-50
Aim Smooth: (depends on your GPU but usually 15-25)
TROUBLESHOOTING1
Aimbot is shoppy and not smooth:
Make sure R6 is not consuming all of your GPU, check it by opening your Task manager on second screen (or on same screen with option “Always on Top”, then check GPU usage while running arounbd in R6. It must not exceed 70-80 %
If VanuriClient cannot find the Raspberry Pi it is one of the following reasons:
Tip: You can test general network communication by opening CMD and typing ping mediapro2
Before opening VanuriClient, you didn’t freshly boot up the Raspberry Pi.
You didn’t wait at least 120 seconds after you plugged in the USB cable into the Raspberry Pi
You are not in the same network as the Raspberry Pi
The micro SD-Card flash failed
TROUBLESHOOTING 2
If you cannot move your mouse after VanuriCleint has flashed + spoofed your Raspberry Pi this may be the issue:
You are using a wrong USB-C to USB-C/ USB 3 cable. Phone Cable, power only cable and USB 2 cable won’t work
You plugged in the USB cable in a USB 2 port
You plugged in the USB cable in a front USB port
